You can maintain brick floors with relative ease, but it has to be cared for regularly to keep it looking its best. Dust and dirt can collect in the mortar between the bricks. Sweep or vacuum the brick daily to remove dirt and grit that hides in the crevices. Tiny grains can act like sandpaper on a brick floor and, over time, wear down any sealer on the floor and damage the brick itself.
How Often to Clean Brick Floors
In addition to an everyday sweep or vacuuming, it’s a good idea to clean your indoor and outdoor brick flooring weekly. Begin your weekly cleaning by thoroughly sweeping, vacuuming, steam cleaning, or dry-mopping the floor to remove any dirt or particles clinging to the surface.
Equipment / Tools
- Broom or vacuum
- Towel, washcloth, or dry mop
- Nylon scrub brush (optional)
- Steam cleaner (optional)
- Brick, stone, or tile cleanser; vinegar; Borax; or baking soda
How to Clean Brick Floors With a Cleaning Solution
Sweep or Vacuum the Brick
Sweep or vacuum the brick to remove the dirt and grit in the grout and crevices.
Make or Buy a Cleaning Solution
Either buy a cleaning solution for natural stone, brick, or tile or make a homemade solution using vinegar, Borax, or baking soda as your active ingredient and mix it with water (recipes below) in a bucket.
Mop the Brick Flooring
Dunk a mop into the cleaning solution and wring it out thoroughly so that it is no more than slightly damp. Mop the floor using a vigorous back-and-forth motion to remove stuck grease, dirt, or stains. If necessary, use a stiff nylon scrub brush to attack stubborn dirt and grime.
Wipe Off the Liquid
After mopping, you may want to go over the floor with a soft towel, a washcloth, or a dry mop to remove liquid from crevices and grout joints. A fast wipe will prevent streaking and smudges as the floor dries completely.
How to Deep Clean Brick Floors
Use an Acid or Sulfate-Based Cleaner (Option 1)
If your brick has excessive accumulated dirt, you will need a stronger cleaning solution, such as a commercial brick acidic cleaner or sulfate-based cleanser. Read cleaner labels carefully, and follow the manufacturer’s directions to prevent etching or discoloration of the brick.
Pressure Wash or Steam Clean the Brick Surface (Option 2)
Instead of chemicals, try using a pressure washer or steam cleaner to remove tough, set-in stains. Take note: Rough scrubbing or too strong pressure washing can scratch or mark the brick. Use a flat- or fan-spray nozzle on a pressure washer, and keep the nozzle a safe distance from the brick surface.
Tips to Keep Brick Floors Clean Longer
- Sealing a brick floor or fireplace will make it easier to clean.
- Freshen periodically with commercial brick cleaner.
- Scrub grout lines with cleansing agents. In extreme cases, you can also completely remove and reinstall the grout.
DIY Cleaning Solution
You can make a DIY cleaning solution using vinegar, Borax, or baking soda as your active ingredient.
- Vinegar-based solution: Mix 1 part vinegar with 10 to 15 parts water
- Borax-based solution: Mix 2 tablespoons Borax with 1 gallon of water
- Baking soda-based solution: Mix 1 to 2 tablespoons of baking soda with 1 gallon of water
Removing Stains From Brick Floors
Brick is susceptible to stains from mortar, mildew, rust, paint, graffiti, and more. You can acid wash, bleach, or use commercial cleaners made to clean brick. Home remedies for hand cleaning soot stains include using a vinegar and water solution or water-diluted laundry detergent. Use a cleaning solution with liquid dish soap or laundry detergent mixed with water for oil stains.
Removing Dust From Brick Floors
When new, indoor brick flooring may have pale, fine dust that emits from its surface. This dust can cause a mess when tracked by feet to other floors. Usually, this dust is caused by using muriatic acid to clean the brick after bricklayers initially installed it. If this acidic substance is not flushed away thoroughly, it can remain in the grout lines, causing the dusting effect.
You can solve this problem by continuously flushing the floor or brick face with clean water to remove all muriatic acid traces in the grout lines. Use a damp mop or a sponge repeatedly until the dusting effect stops completely.